The following instructions are for programming a Genie garage door opener intellicode remote. If you have an older model Genie opener you may need to follow a slightly different procedure.  These instructions should also allow you to clear all the programming codes from your opener. Clearing the codes from the opener’s receiver is the only way to disable a lost remote.

Make sure to keep everyone, including pets, out of the path of the garage door when programming a remote or keypad.

1. Locate the “learn” button on the opener. The location of the learn button is dependant upon the model opener. It can typically be found under the light cover. The learn button will have a small indicator light next to it.
2. Press and release the learn button
3. Press and release the button on the remote.
4. Press and release the button on the remote once again.

That’s it. The remote should be able to operate the opener at this point. Repeat these steps for any additional remotes or buttons you may wish to program.

To clear all existing codes from the receiver:

1. Press and hold the learn button on the opener for 10 seconds, or until the indicator light goes out.

Clearing the codes will erase all programming from the receiver. This feature is useful if  a remote has been lost, or if you wish to disable any old remotes or keypads. After clearing the codes,  remotes or keypads will need reprogramming.

Many of our Atlanta area customers have come to us for advice on programming remotes and keypads. We’ll always be happy to answer any questions or help with any problems,  but the following steps will allow you to re-program after changing the batteries, or clear all the old codes and start over. We recommend reading over all the instructions to see which method will work best for your situation. Click here for a printable version of these instructions.

The steps for programming your opener’s remote and keyless entry can vary for different models and brands. Many openers will allow for programming from the wall button, as well as from the opener.

Method #1 – With a step ladder to reach the opener. You’ll need to locate the “Learn” button on the opener, under the light cover. It’s usually a square button with a tiny LED next to it.

Both methods described here simply add to the codes already in use for the opener. In order to clear all the old codes from previous remotes/keypads you’ll need to press and hold the Learn button for about 6 seconds. The indicator light next to the Learn button will go out. Then follow the directions below to re-program any remotes or keypads to be used.

Method #1 – With a step ladder to reach the opener.

There are three basic steps when programming a remote:

1. Press and release the “Learn” button on the opener.

2. Press and HOLD the button on the remote

3. Wait for the light bulbs in the opener to flash, and release the remote’s button. If there are no light bulbs on the opener, you should hear one or two clicks.

Programming a keyless entry is basically the same as a remote. We just need to enter the PIN before pressing Enter on the keyless entry/keypad.

1. Press and release the Learn button on the opener

2. Enter your desired 4-digit PIN, and HOLD Enter.

3. Wait for the light bulbs on the opener to flash, and release the Enter button. If there are no light bulbs on the opener, you should hear one or two clicks.

Method #2 – With Multi-Function Door Control

Since both of these methods require the use of a ladder to reach the Learn button, LiftMaster has provided an alternative way to program remotes using the keyless entry and the wall button. In order to use this method, you must have two people and a multi-function wall button (one that allows you to turn the opener lights off and on).

1. Enter your 4-digit PIN into your keyless entry, and HOLD Enter.

2. The second person will press and hold the Light button on the wall button.

3. While still holding the buttons, press and hold the remote’s button until the opener lights flash. If there are no light bulbs on the opener, you’ll hear one or two clicks.

Bookmark this page:

]]> http://curbappealcsi.com/liftmaster-craftsman-and-chamberlain-garage-door-openers-how-to-program-a-remote/feed/ 0 http://curbappealcsi.com/why-wont-the-garage-door-go-up-3-most-frequently-asked-troubleshooting-questions/ http://curbappealcsi.com/why-wont-the-garage-door-go-up-3-most-frequently-asked-troubleshooting-questions/#comments Thu, 02 Jul 2009 18:52:27 +0000 admin http://curbappealcsi.com/?p=493 We receive plenty of questions from homeowners here in metro Atlanta, GA about their garage doors and openers. While there can be wide variety of questions, most revolve around the following three issues.

1. Why does it reverse back up instead of closing?

Most likely, your safety eyes are out of alignment, or something is blocking the path of the garage door. The safety sensors/eyes need a clear line of sight between each other in order for the opener to travel downward. They’re usually black, and attached at the base of the tracks. Each should have a small LED light that remains lit when both sensors are properly aligned. If bumped out of place, they can be adjusted by hand so that they are pointing at each other again. It’s fairly common for the lenses on the safety eyes to become obscured by dirt or other debris, as well. Take a look at this post for more troubleshooting advice on garage door openers.

2. Why is it so heavy?

Garage doors are generally at least 8′ wide and 7′ high. That amount of material can really tip the scales, making it the largest moving piece of machinery in your home. That’s why there are springs and a counter balance system to take all that weight, and make it manageable. Remember manual keylocks, and doing things by hand? Openers don’t (or shouldn’t) pull any more weight than a person would when doing that job. That being said, springs can relax over time, making things heavier. Stripped gears, which are a very common repair, are caused by this type of problem.  It’s generally a good idea to do some maintenance about once a year. Have a professional check for proper spring tension, and adjust them if needed.

3. Why won’t it go up? / Why is it stuck in the down position?

Take a look at the springs located on the wall above the garage door. There should be no break, or separation in the coils. Springs generally last for about 7 years, depending on the amount of daily usage. Again, these provide the force for balancing out all that weight. When one breaks, it can make things too heavy to lift, causing it to seem stuck in place. If one of yours is broken, you’ll probably need to call a pro. If you’ve seen no separation in the coils, try pulling the emergency release. This will allow manual operation, without the motor. It may be that they’ve relaxed to the point that the opener can’t lift the weight anymore.

Hopefully, some of your questions have been answered. If you still have issues that weren’t covered here, you may want to take a look at our blog. We also have links available for manufacturer sites. Most manufacturers will offer online access to owner’s manuals. Manuals for your model product are the best source for learning how to safely troubleshoot, and maintain your system.

Alpharetta Buckhead Buford Chamblee Clarkston Cumming Decatur Doraville Druid Hills Duluth dunwoody Emory flowery Branch Gainesville Grayson Kennesaw Lawrenceville Lilburn Lithonia Loganville Marietta Norcross Oakwood Roswell Sandy Springs Smyrna Snellville Stone Mountain Sugar Hill Suwanee Tucker

Bookmark this page:

]]>